How do you adjust a gas fireplace valve?
If you want the flame higher we’ll lower it’ll say to increase it or decrease it. Or I’ll say high and low and you just rotate it around according to what you what you would. Like.
Table of Contents
How do you adjust the pilot pressure on a gas valve?
To REDUCE pilot pressure, turn the pilot adjust screw (beneath the cover screw) clockwise ( ). To INCREASE pilot pressure, turn the pilot adjust screw counterclockwise ( ). Replace and tighten cover screw. adjusting screw beyond the limits that it can easily be adjusted.
How high should the pilot light be on a gas fireplace?
If the system is working well, the color of the pilot light will be blue with yellow. The light should be about half-inch long to cover the end of the thermocouple tip. If the pilot flame is not well-tuned, and the flame is too forceful, it will further malfunction and create noise.
What is pilot position on gas fireplace?
The pilot position on a gas fireplace is the position on the fireplace controls that is used to start the pilot flame. The pilot position is typically set on the control dial with either the dial depressed and turned, or used with a separate spark button to light the pilot flame.
Where is the pilot light adjustment screw?
Next to the “Pilot” indicator on the furnace’s control switch, there is a small screw located near the pilot light-thermocouple assembly.
Can you adjust the flame on a gas fireplace?
The Gas Fireplace Flame Color adjustment knob is located on the front of your gas fireplace and is used to adjust the color of the flames. Turning the knob clockwise will make the flames more yellow, while turning it counter-clockwise will make them more blue.
Where is the pilot adjustment screw?
How To: Adjust the pilot flame – YouTube
What should pilot gas pressure be?
When checking the incoming pressure be sure to have everything that uses propane on and running on high fire. Proper gas pressure out should be; LOW FIRE 6.7” w.c. to 7.3” w.c. and HIGH FIRE 9.7” w.c. to 10.3” w.c.. Natural Gas; The input pressure should be approximately 5.5” w.c. to a max of 10.5” w.c..
Can the pilot light on a gas fireplace be adjusted?
On some fireplaces, there will be a “Lo-Hi” button that allows you to adjust the flame upward or downward. On others, there will be a screw that you can easily adjust with a screwdriver. Turning the screw clockwise will lower the flame, while a counterclockwise motion will turn it up.
What happens if pilot light is too high?
If the pilot flame is too long it will not reach the sensors and they could not ignite the system. Also, the bright orange light does not provide the temperature needed for the thermocouple to work. It probably would not cause any damage to the system, but it may have issues with the ignition.
Should the pilot light always be on in a gas fireplace?
The pilot light needs to run continuously because, without it, the gas going into the fireplace would not have an ignition point. This would lead to fireplaces or entire gas fireplace inserts filling up with gas when they are turned on.
Is it OK to leave the pilot on a gas fireplace?
Generally speaking, it is safe to leave your continuous pilot light on at all times, assuming it stays lit (more on this in a moment). While it does cost more to keep your pilot light on in between uses, it can actually have some benefits to your system.
What is pilot adjustment screw?
Generally the pilot screw adjustment procedure involves turning the pilot screw in or out in small increments until the idle climbs as high as it will go. Return the idle to specification with the idle adjuster.
Why is my pilot light flame too high?
So, if your pilot light flame also tends to be too high, ensure that your fireplace doesn’t have a button to bring the flame up or downward. If there’s no such button, adjust a screw on the fireplace. Turning it clockwise will reduce the fire whilst moving the opposite direction will raise it.
Why is my gas fireplace flame so small?
The little flame you see in your gas fireplace after you have turned it off is called a pilot light. A Standing Pilot Light runs constantly, whether your fireplace is on or off.
What does the pilot air screw do?
What does it do? A pilot air screw will be made of brass, gold in color, and will have a blunt tip compared to a pilot fuel screw. The pilot air screw meters air, so turning it clockwise/in will richen the fuel/air mix, while counter-clockwise/out will lean the fuel/air mix.
What happens if gas pressure is too high?
High gas pressure can be just as bad for your furnace. That’s because it greatly increases the risk of furnace overheating. When this happens, all manner of internal components may become damaged by the excessive heat.
How do I check the gas pressure in my fireplace?
Diagnostic Testing For Gas Pressure And Gas Millivolt Valves – YouTube
Are gas fireplace pilot lights safe?
How do you reset the pilot light on a gas fireplace?
How To Light a Pilot in a Gas Fireplace – YouTube
Does a pilot light produce carbon monoxide?
It could be dangerous. But if your pilot light is yellow, or even if has a slight yellow or orange tint, then wasted energy may be the least of your concerns. A yellow or orange pilot light will produce carbon monoxide – an odourless, colourless gas that can fill your home and cause carbon monoxide poisoning.
Does a pilot light use much gas?
Just how much gas does a pilot light consume? Most pilot lights will consume about 600 BTU’s of gas/hour. With 24 hours in a day, that’s roughly 14,400/BTU’s each day. Figuring 30 days, a pilot light will use approximately 432,000 BTU each month.
Does pilot screw adjust fuel or air?
Pilot Air/Fuel Screw Adjustment Explained – Single Carb – Part 1
How do you turn on a pilot screw?
Whilst taking note of the position of your screw, rotate slowly in one direction until you hear the idle begin to slow then slowly reverse direction until, once more, you hear the idle begin to slow. Then set the screw exactly between those two points.
Can pilot lights be adjusted?
If the pilot flame is too small, you may be able to make it larger by turning the pilot adjustment screw on the valve control counterclockwise with a screwdriver to open it. If this screw isn’t labeled, consult the appliance owner’s manual to identify it.