What does trimming the tip of a golf shaft do?
Shaft tipping is when a club builder removes length from the tip section of a shaft, which is the end where the clubhead is installed. In most cases, tip trimming a shaft makes it meaningfully stiffer. It also increases torsional stiffness, known as “torque,” which is a shaft’s resistance to twisting.
Do you tip trim iron shafts?
Instead of stocking individual shafts for every club, the same shaft can be tip trimmed to fit any iron club. In additional to trimming the tip, you’ll then need to trim the butt end, to achieve the final desired club length.
What is difference between KBS Tour and C-Taper?
The Tour is stiffest in the grip section (for good feel) and it gives mid-launch and mid-spin. The C-Taper is stiffest in the tip section (close to the head) to give a stout and strong feel and deliver low launch with low spin.
How do you trim a parallel shaft?
So those trimming instructions are going to tell you how much to trim off the tip. Section to create a specific shaft that say goes in a nine iron or eight iron or seven iron.
How does tip trimming affect Flex?
In general, tip trimming can be used to achieve a stiffer shaft profile, lower launch, and/or lower spin. Tip trimming 1“ is equivalent to one flex. For example, if you wanted to stiffen your S flex to an X flex then you would tip trim 1”. If you prefer to play shaft in between S and X flex, you would tip trim 1/2”.
Does shortening golf shaft make stiffer?
A shorter shaft is typically stiffer than a longer one. Although a shorter golf club shaft tends to be firmer than a longer one, it is important to understand the changes trimming a shaft will make to a club before making such a permanent change.
Which end of a golf shaft do you cut?
The butt end of the shaft is grip end. If you are shortening or extending the length of a golf club, this is where you will cut. If you want to change the play-ability of the club (feel, flex to a certain extent, spin rate, dispersion), you will be cutting the tip end of the shaft.
What iron shaft is best for me?
Which flex rating you use will depend on the type of swing you have. For example, beginners and those with less powerful swings tend to use a shaft with greater flexibility to propel the ball more. On the other hand, if a player has a high and powerful swing speed, they will require a stiffer shaft with less flex.
What is the difference between KBS Tour and KBS Tour 90?
The KBS Tour 90 shaft is the lightest steel shaft in the KBS lineup and designed to give players more spin, a higher trajectory, and greater swing speeds. Though still a firm shaft design, the Tour 90 has softer tip and higher center of gravity to help players get the ball in air with more distance.
Is it better to hard step or soft step?
“Hard stepping” would make a shaft stiffer, “soft stepping,” more flexible. The effective change in flex between immediate lofts from stepping is 1/3, or 5 cycles per minute, a practically negligible change in performance for most golfers.
Does tip trimming change swing weight?
To decrease length, trim the shaft from the butt, or grip, end (do not trim from the tip of the shaft, as it will stiffen the shaft’s flex). For every half inch of length added, the swingweight increases by three swingweight points.
Will a shorter shaft help my slice?
In addition to using a softer shaft to reduce slices, you could also try going a little shorter as well. A shorter shaft will make it easier to control the clubhead, again, helping you rotate the hands and square the clubface at impact. Furthermore, a shorter shaft will make a flatter swing into a more upright one.
What happens if I shorten my driver shaft?
Shortening the shaft will make the club shorter but it will also make the shaft stiffer and adjust the swing weight as well. Plus, the more length you remove, the less flex your club will have. Depending on how much you cut it down, it could move a regular flex to a stiff or a stiff to an extra stiff.
Should I cut my driver shaft down?
Should shorter golfers choke up?
By choking up and making the club shorter, it’s easier to accelerate and get the ball out of the thick stuff so you can have more putts to save par. Remember, acceleration is key to being a great short game player!
How far should you hit a 7 iron?
Average 7 Iron Distances are following:
Beginning golfers- 100 yards (men) or 60 yards (women) Intermediate golfers- 135 yards (men) and 75 yards (women) Advanced golfers- 165 yards (men) or 140 yards (women) PGA Tour Players- 185 yards (men) or 160 yards (women)
What shaft should I use with a 90 mph swing speed?
stiff shafts
80-95 mph swing speeds should use regular shafts. 90-105 mph swing speeds should use stiff shafts.
Is KBS Max 80 a good shaft?
KBS MAX 80 is a lightweight shaft for mid-high handicap players. It produces a high trajectory and spin rate for longer distance shots. KBS MAX 80 designed for players seeking to maximize the performance of their irons.
What is the lightest KBS shaft?
As the lightest shaft in the KBS product line, the KBS TOUR 90 is designed for players seeking higher trajectory, additional spin and maximum distance. The KBS TOUR 90 is 20% lighter than standard shafts, ultimately assisting to increase swing and ball speeds.
Does soft stepping add distance?
Soft stepped golf clubs also provide an increased distance off the tee than regular golf clubs do. This is due to their larger sweet spot, making it easier for them to make contact with the ball, even on bad swings or shots that don’t land squarely on the clubface.
Does soft stepping change length of club?
Soft stepping is going to make the club a bit longer and softer. It’s typically done by using a 3-iron shaft in a 4-iron head, for example, and making the club play 1/3 of the flex softer, leading to higher ball flight. You can also tip trim to achieve similar results.
What is a good swing weight for a senior golfer?
A swing weight between C-8 and D-1 is the best swing weight for a senior driver, and the shaft should be 55-60 grams. Loft should be 12-13 degrees or higher, and seniors should look for 2-4 degrees of hook in the face or consider an offset driver head to prevent slicing.
Does shortening a shaft increase swing weight?
For every half inch of length added, the swingweight increases by three swingweight points. For every half inch of length removed, the swingweight decreases by three swingweight points.
Is it OK to shorten a driver shaft?