What are the error codes for Amana washer?
Error Codes in my Amana Front Load Washer
Table of Contents
| Error Code | Error |
|---|---|
| Sud or Sd | There are too many suds in the washing machine. |
| F5 E2 | The door is not locking properly. |
| F7 E1 | Indicates a motor speed sensing error, |
| F8 E1 or LO FL | The washer is sensing a low flow of water. |
What does E1 and F9 mean on a Amana washer?
F9 E1 Code in the display:
This error code indicates that drain times are longer than expected, typically over eight (8) minutes.
How do I reset my Amana front load washer?
First, unplug the washing machine for a few minutes that will reset the machine and clear the flashing light. Press and hold the End of Cycle or Cycle Signal button for twenty seconds. This process also reset your Amana washer and clear the flashing light.
How do you fix error E1 F9 on a washer Amana?
The drain hose may be too far down inside the drainpipe (standpipe) or laundry tub. Drained water can siphon back into the washer if the drain hose extends too far. Make sure that the drain hose does not extend more than 4.5″ (113 mm) into the drainpipe or laundry tub.
How do you read a washer error code?
How to Read a Vertical Modular Washer (VMW) Error Code Display
Why is my Amana washer stuck on sensing?
Try to reset it
Turn the washer off and un-plug it from wall outlet. Then after about 60 seconds, plug the washing machine back in. Then, within 30 seconds(of plugging it back into the electrical outlet), fully open then close the machine’s lid six times (in a row).
How do I fix error code F9?
Reset the Oven
Sometimes, the F9 error code is the result of an electrical fault that has magnetized the circuitry. Resetting the oven by disconnecting the power for five minutes will demagnetize the circuitry and resolve the F9 error.
What does F9 mean on front load washer?
May 4, 2022. A Whirlpool washer error code E1/F9 occurs when the washer’s control board detects that the washer cannot drain. Therefore, to resolve the E1/F9 error code, the washer components responsible for draining will need to be checked and possibly replaced.
How do I put my Amana front load washer in diagnostic mode?
How to Use Troubleshooting Mode on a Whirlpool, Maytag or Amana …
How do I recalibrate my Amana washing machine?
How to Calibrate a Top-Load Washer – YouTube
What does E9 mean on washing machine?
E9 indicates that the load exceeds the rated capacity or clothes are close to the inner cylinder wall before drying.
How do I put my Amana washer in diagnostic mode?
How do I recalibrate my Amana washer?
How do I put my Amana washing machine in diagnostic mode?
How do I read my Amana washer code?
Amana Washer Error Codes – YouTube
What does F9 error code mean?
2. If the Control Panel Display lights up error code “F-9” it means oven failed at exceeding 150ºF after 5 minutes of preheating.
How do I fix error code E9?
For error code E9 or E09 on an Induction Cooktop, turn the home circuit breaker to the unit off for 10 seconds. Turn back on again and then retest the unit operation. If these troubleshooting steps do not resolve the issue, service is necessary to expertly diagnose and repair the product.
What does F9 mean on a washing machine?
Often when a Whirlpool washer displays an E1/F9 error code, it is the drain pump that is causing the error code. The drain pump can become defective if it is clogged, the impeller breaks, or if an electrical fault causes the pump to fail.
What is E1 error in washing machine?
2022. When the Washing Machine is displaying E1 in the panel, it is indicating an error in the water supply. The appliance is not detecting that the unit is filling with water. To resolve, checking the following: • Check whether the water supply is turned on and that there is adequate water pressure.
How do I fix E1 error?
If the E1 error code appeared as a reminder to clean the air filter, turn off the unit, and then open the front panel and remove the filter. Clean it with soap and water and let it dry before replacing it. If you can’t remove all the dirt and grease it has collected, it’s time to replace it.
How do I clear E1 on my washing machine?
Clogged Inlet Valve
- Turn off the washer and unplug it.
- Take off the water valves.
- Remove any debris that may be blocking the valve.
- Brush it with distilled white vinegar.
- Once the valve is clear, reattach the water valves and turn on the power to the washer.
How do I fix E1 error on washing machine?
E1 – water inlet alarm
- Check that the water faucets are not closed.
- Check that the water pressure in the house is over 20 kPa.
- Clean the inlet hose filter screens. Be careful not to remove or disturb the screen placement.
- Check that the drain hose is not below 27½” (700 mm) from the floor.
Why does my washing machine keep saying E1?
The E1 error on a washing machine is an indication that there is a problem with the water supply. The most common causes of the E1 error are a clogged inlet valve, a failed inlet valve, or maybe an issue with failed water level sensor.
How do I fix error code E1 F3?
F3 E1 Error Code
Power unit down by turning off the circuit breaker or unplugging for one (1) minute. Power unit up by reconnecting power. Restart a new cycle. Monitor the washer for one (1) minute to ensure the error code does not display again.
How do I fix f2 E1 error?
Reset power to the product:
Power unit down by turning off the circuit breaker(s) for one (1) minute. Power unit up by turning on the circuit breaker(s). Monitor the oven for one (1) minute to ensure the error code does not display again. Verify oven operation.